News

1. To choose a suitable material for cutting a hole saw drill bit based on one's own processing material properties, and to know what one's needs are, otherwise buying it and not using it would be embarrassing? At present, the main materials for drilling tools include bimetallic, hard alloy, diamond coating, alloy tool steel, high-speed steel, etc. Different materials have different properties; 2. The selection of hole diameter and depth. Due to its own rotational speed and cutting properties, when selecting a hole saw drill bit, it is important to pay attention to selecting a hole size that is suitable for oneself. The hole depth should be determined based on one's own material. In general, it is recommended that the depth of the hole saw drill bit be less than 10mm when drilling metal holes. 3. The selection of tooth number and pitch has different cutting properties. We determine the suitable tooth number and pitch based on the hardness and thickness of the cutting material, as well as the structural characteristics of the material. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

The bimetallic hole opener with M42 bimetallic teeth ensures smooth sawing and is suitable for materials such as building materials, thin iron sheets, and thick cast iron, with a wide range of applications; The bimetallic hole saw drill bit has the strongest resistance to tooth detachment among all metal hole openers, so even if other metal hole saw drill bits are not good at making holes in materials such as round pipes and thick plates, the bimetallic hole opener can still be competent. Currently, it is widely used in the installation of fire pipelines and round pipes; The product specifications are the most complete, ranging from 13mm to 230mm, including various non-standard specifications and can be customized in small quantities. Points for Attention: 1. Always wear eye protection glasses when using; 2. Ensure that the drilling material is tight and avoid rotation; 3. Refer to the tachometer and adjust the drilling speed for different sizes and materials; 4. When opening a hole, it should be perpendicular to the surface of the material being cut, and remember to tilt it to prevent the edge from cracking due to high-speed rotation; 5. When drilling thick plates, pipelines, and other materials that require the removal of springs, the springs can be removed, but the drill bit must not be removed. When the handgun drill is running at high speed, the hole opener is not positioned, which is prone to deviation and is very dangerous. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. Grinding bits generally use grinding wheels with a particle size of 46-80 mesh, and aluminum oxide grinding wheels with medium to soft hardness are preferred. It is required that the grinding wheel runs smoothly, and grinding wheels with large runout must be trimmed. In order to smoothly grind the transverse edge of the drill bit, the outer corner of the grinding wheel must be trimmed to a smaller radius. If the radius of the fillet is too large, it will damage the main cutting edge when grinding the transverse edge. 2. When the drill bit is cooled, the pressure applied by the drill bit during grinding should not be too large. Generally, air cooling is used, and if necessary, water should be dipped for cooling to prevent overheating and annealing from reducing the hardness of the cutting part of the drill bit. 3. The standard Fried Dough Twists drill has a long horizontal edge, which is generally 0.18D (D refers to the diameter of the drill bit), and the front angle at the horizontal edge has a large negative value. Therefore, the cutting at the horizontal edge is in an extrusion state when drilling, and the axial resistance is large. At the same time, the length of the horizontal edge causes poor centering effect and cutting stability. Therefore, the drill bit with a diameter of more than 5mm must have a short horizontal edge, and the front angle near the horizontal edge should be appropriately increased to improve the cutting performance of the drill bit. The grinding of the transverse edge is necessary. The purpose of transverse edge grinding is to shorten the transverse edge, but it cannot be too short. A too short transverse edge cannot reduce the feed resistance. During the process of shortening the transverse edge, try to grind the negative front angle on both sides of the transverse edge as much as possible. Properly increasing the front angle at this point can reduce the cutting resistance during the cutting process, making the entire drilling process light and fast. 4. If the drill bit is manually fed. The tip angle can be appropriately reduced during the grinding process. Due to insufficient feed pressure of the electric hand drill, reducing the tip angle appropriately can increase the positive pressure of the cutting edge on the cutting surface. If the requirements for the aperture and surface roughness of the processed hole are not very strict, the two cutting edges can also be appropriately ground into incomplete symmetry. Although the hole diameter will increase on the original basis during the drilling process, it can significantly reduce the friction between the drill bit edge and the hole wall, reducing cutting force. There is no strict formula for grinding drill bits, which requires gradually accumulating machining experience in the actual operation process, constantly repeating experiments, gradually comparing, and observing, to ensure that the drill bit edge can be ground well. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

Fried Dough Twists drill is a commonly used drilling tool with simple structure. Grinding the drill edge is very important for workpiece processing, but it is not easy to grind it properly. The key lies in mastering the methods and techniques of blade grinding. With the mastery of these methods and the experience of multiple blade grinding, one can effectively grasp the grinding scale of the drill bit. Before grinding the drill bit, first place the main cutting edge of the drill bit on a horizontal plane with the grinding wheel surface, which means that when the blade contacts the grinding wheel surface, the entire blade must be ground. This is the first step in the relative position between the drill bit and the grinding wheel. Once the position is set, slowly lean against the grinding wheel surface. 2. This angle is the sharp angle of the drill bit. If the angle is not correct at this time, it will directly affect the size of the top angle of the drill bit, the shape of the main cutting edge, and the oblique angle of the transverse edge. This refers to the positional relationship between the axis of the drill bit and the surface of the grinding wheel, which can be seen accurately by taking 60 °. Here, it is important to pay attention to the relative horizontal and angular positions of the drill bit before grinding. Both should be considered comprehensively, and do not neglect to adjust the angle or adjust the blade to adjust the angle. 3. After the cutting edge contacts the grinding wheel, it should be ground from the main cutting edge to the back face, that is, starting from the cutting edge of the drill bit to contact the grinding wheel first, and then slowly grinding down the entire back face. When the drill bit is cut in, it can gently touch the grinding wheel. First, perform a small amount of edge grinding, and pay attention to the uniformity of the spark. Adjust the pressure on the hand in a timely manner, and also pay attention to the cooling of the drill bit. Do not let it grind too much, causing discoloration of the edge, and even annealing of the edge. When the temperature of the cutting edge is found to be high, the drill bit should be cooled in a timely manner. 4. This is a standard drill bit grinding action, where the main cutting edge swings up and down on the grinding wheel, meaning that the hand holding the front of the drill bit should evenly swing the drill bit up and down on the grinding wheel surface. The hand holding the handle cannot swing, and it is also necessary to prevent the rear handle from tilting upwards, that is, the tail of the drill bit cannot be raised above the horizontal centerline of the grinding wheel, otherwise it will make the cutting edge blunt and unable to cut. This is the most crucial step, and whether the drill bit is ground well or not is closely related to it. When the grinding is almost done, start from the edge of the blade and gently rub against the back corner to make the back of the blade smoother. 5. After grinding one edge, grind the other edge, ensuring that the edge is in the middle of the drill axis and the edges on both sides are symmetrical. Experienced masters will observe the symmetry of the drill tip in front of the bright light and slowly polish it. The back angle of the cutting edge of a drill bit is generally 10 ° -14 °. If the back angle is too large, the cutting edge is too thin, causing severe vibration during drilling. The hole opening is triangular or pentagonal, and the chips are needle shaped; The back angle is small, and the axial force during drilling is large, making it difficult to cut in. The cutting force increases, resulting in a large temperature rise and severe heating of the drill bit, making it even impossible to drill. The back angle grinding is suitable, with the sharp point centered and the two edges symmetrical. During drilling, the drill bit removes chips quickly and without vibration, and the aperture will not expand. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. Machine tool structure The standard configuration of the linear axis (X, Y, Z) is a grating ruler, and the rotating axis adopts a DD direct drive motor, achieving high-precision positioning and indexing accuracy. 2. Measures to prevent thermal deformation The machine body is designed with a symmetrical structure that minimizes the impact of thermal deformation. To achieve stability during long-term continuous machining and high-precision production of cutting tools. Equipped with an automatic cooling liquid circulation function on the bed after startup, the cold cutting liquid will circulate even without grinding, ensuring a balanced temperature of the body and more stable processing accuracy. 3. Grinding wheel spindle The spindle end of the grinding wheel adopts a 2-sided binding structure of HSK-C40. Ensure the jumping and repetitive accuracy of the grinding wheel shaft during locking. 4. Working spindle The rotation of the work spindle adopts a direct drive motor to eliminate the influence of clearance and ensure accurate indexing angle. A standard workpiece support frame that can greatly improve the jumping accuracy during workpiece clamping. 5. Automation device The long-term unmanned production of built-in loaders has increased the number of loaded items and improved the convenience of use compared to previous machines. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

White: Fully ground high-speed steel drill bits often appear in white. In addition to the material itself, the quality control during the processing of fully ground high-speed steel is strict and the quality is high. Of course, rolling drill bits can also achieve white color by finely grinding the outer circle. Black: Place the finished product in a mixture of ammonia and water vapor, and the drill bit that has been insulated and nitrided at a certain temperature is black. Of course, black drill bits may also be made of carbon tool steel, as carbon steel is prone to rust, so it usually needs to undergo blackening treatment. Yellowish brown: Referred to as cobalt containing diamonds in the industry, cobalt containing diamonds are produced by grinding. Originally white, they were later atomized to form a yellowish brown color. Its hardness can reach HRC54. Gold: Titanium plated diamond, industrial plating hardness can reach HRC78. Of course, there is also decorative plating, as the name suggests, decorative plating is just for the sake of appearance. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. Nowadays, it is common to punch holes in beams during the decoration process. Because no matter what beams or columns are used for load-bearing purposes, they are all reinforced concrete structures with high stability. As long as they are not removed, there is not a problem of drilling holes on them. 2. When drilling holes on the beam, be careful not to make them too large. If only one hole is drilled to route the pipeline, there is no problem. When selecting the location, be careful not to be in the center of the beam (column) as the steel bars in the center are dense, which may cause danger such as collapse. 3. When drilling holes in the decoration beams, we should also avoid removing the steel bars inside, as the steel bars have a load-bearing function and once removed, it will affect the overall structure of the house. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. The choice of punching holes on both sides of the beam is the safest because the stress on both sides is the smallest and does not have a load-bearing effect. If you choose to hit the middle of the beam, it will actually damage the load-bearing effect of the beam. 2. The traditional concept holds that load-bearing beams cannot be perforated, but in fact, they are not. The drilling of load-bearing beams only requires selecting the appropriate position, taking necessary safety measures, and selecting the appropriate position accurately. Generally, decoration masters will focus on the specific location and develop a reasonable drilling plan in the early stage. 3. Punching holes on the beam poses certain risks, so temporary reinforcement should be considered first, such as adding temporary support objects below the beam. To ensure that the quality does not continue to develop and cause other losses, the original design unit or a design unit with corresponding qualifications are entrusted to carry out structural reinforcement design, and design documents with the signatures of structural engineers and design institutes are produced. 4. The drilling on the beam not only requires selecting the appropriate position, but also the appropriate size. If the drilling diameter is greater than 100, drilling is generally not allowed and has potential safety hazards. If drilling is necessary, the location of the drilling needs to be approved by the property design institute before execution. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. Understand the schematic diagram of each hole position before drilling, understand the structure and internal and external conditions of the house; 2. Clearly mark each hole position and observe the direction of the water and electricity pipelines; 3. Punch holes on both sides of the beam as much as possible, with minimal stress on both sides; 4. Punch holes as much as possible on beams with walls below; 5. Try to punch holes at the top of the beam as much as possible, with less stress on the top; 6. Make small holes on the beam as much as possible; 7. The height of the beam is 20 centimeters and no upper or lower holes are allowed; It is strictly prohibited to drill holes at the bottom five centimeters of the beam. Usually, there is a main reinforcement three centimeters below the beam, and it is strictly prohibited to hit the main reinforcement. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

① Avoid punching at the inlet of the pipeline: In some places where there are no switches, it is possible to roughly draw the dense areas of the pipeline through the entrance of the pipeline, and try to avoid drilling at positions that appear particularly cumbersome for pipeline laying. ② Avoid punching at corners: When laying pipelines, the pipeline is mostly laid at the corners to avoid drilling holes at the corners. ③ Avoid punching at the connection: Try to avoid drilling holes in the direction of the water pump and interface connected to the pipeline. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

The selection of tools and drill bits must match the material of the tiles and the size of the holes. If it is a floor tile or a full tile, an electric hammer cannot be used, and a glass drill bit should be used for the drill bit. The correct operation method should be: First, use a hand electric drill with a glass drill bit to drill holes on the entire ceramic tile, and then replace the impact drill with a triangular drill bit to drill holes on the wall When you need to drill holes with a diameter of 20mm or larger, you need to choose a dedicated tile opener. All porcelain has the characteristics of high density and hardness. Do not use impact drills with triangular drill bits for operation, as high-frequency vibration can easily cause cracking. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

Avoid ceramic tile corners and at the intersection of ceramic tiles When measuring, if the punching position is at the corner of the ceramic tile, it is necessary to plan the installation position again to avoid the corner position of the ceramic tile. When applying tiles at the corners, less cement is used, resulting in less than 1/2 of the actual stress position of the plastic expansion screw. As the gravity of the object on the wall pulls downwards, it is easy to cause the object to fall off. Try to choose the center of the ceramic tile without any hollowing and drill down The correct operation method should be: Before drilling: Confirm whether the ceramic tiles at the drilling position are firmly pasted and whether they are hollow. When drilling: Try to choose the center of the tile without any hollowing out. If you need to drill in areas with voids, it is best to use a glass drill to slowly drill. The position where the hole is punched must be tightly adhered to the tiles. If the lower hole is located at the junction of multiple tiles or there is a cavity under the tiles, it is easy to break the drill bit or shatter the tiles during the drilling process. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

The position should be precise Before drilling, it is necessary to use a marker to mark the position of the hole, and the drill bit should accurately and steadily drill the ceramic tile along the hole position. The angle should be perpendicular When drilling, try to maintain a 90 degree right angle between the drill bit and the tile surface, and do not change the angle from drilling down to drilling completion. Use light force to slow down the speed Do not pursue speed or force drilling. There are two benefits to doing this. One is that it can be used to test the approximate hardness of ceramic tiles and the other is to gradually adjust the hole position. The rhythm needs to be adjusted Maintain a constant speed of operation, slowly form a circular "shallow impression" on the surface of the ceramic tile, and then slowly penetrate deeper. If you feel a foreign object sensation during the drilling process, you should stop the operation in a timely manner and carefully investigate before making a decision. Spray water during the process Before drilling holes in ceramic tiles, if a water drill is not used, a water spraying tool should be prepared. During the drilling process, it is necessary to continuously spray water to ensure that there is always water in the position between the drill bit and the ceramic tile, which has a cooling effect. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. Before drilling, mark the position of the hole on the wall with a pencil or chalk, and punch the center of the hole with a center punch; 2. Then select a straight, sharp, non-destructive impact drill bit with the same diameter as the hole; 3. Open the card head, insert the drill bit to the bottom, and tighten the card head with the card head key. Grasp the impact drill with both hands and press the drill tip against the concave hole impacted by the center punch, making the drill bit form a 90 ° angle with the wall; Impact drills are generally not suitable for use as electric drills because: 1. The direction of the impact drill is difficult to grasp during use, which can lead to misoperation and excessive opening; 2. The drill bit is not sharp, resulting in irregular holes, burrs or cracks; 3. Even if there is a conversion switch on top, it is recommended not to drill holes unless you use a dedicated drill bit. However, due to the fast speed of the electric drill, it is easy to blacken the opening and heat the drill bit, thereby affecting the service life of the drill bit. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

The inclination angle of the spiral groove relative to the axis of the drill bit is equivalent to the rake angle of the turning tool. The front angle of the drill bit varies with the position of the cutting edge, with the outer circumference being the largest and the smaller towards the center. At the transverse edge, a negative rake angle is formed, resulting in crushing and crushing of the workpiece material. The large helix angle increases the front angle of the drill bit, resulting in a decrease in cutting torque and axial force. Cutting is light and fast, and chip removal is easy. However, it reduces the strength and heat dissipation conditions of the drill bit, exacerbating the wear of the drill bit. When processing high hardness materials, from the perspective of protecting the cutting tool and reducing wear, it is advisable to choose a small helix angle, while soft materials should choose a large helix angle. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

1. High efficiency drilling, drilling steel material can achieve a linear speed of 40-140 (meters/second); 2. The hole wall has good smoothness. On equipment with good rigidity, the drilling roughness of alloy mold steel can reach Ra3.2 or less; 3. Detachable tool head, achieving quick tool replacement after wear and zero downtime loss; 4. It can achieve good chip breaking of materials; 5. Good centering effect, with good positional and dimensional accuracy of drilling. 6. More suitable geometric angle design for drilling cast iron, enhancing the strength of the cutting edge; 7. Its anti chipping and wear resistance are more compatible with cast iron processing materials; 8. The use of the latest surface treatment technology has greatly improved the wear resistance of cutting tools; 9. The detachable blade design achieves an ultra long service life of the rod drill; 10. The self-locking positioning design of the tool head and body achieves excellent coaxiality and tool cutting stability. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

Crown drill is a high-performance interchangeable drill bit series. The range of drill tip diameter specifications (D12-26mm). You can choose a suitable size drill bit based on the objective conditions of actual production. Crown diamonds are made of cast iron, which is a general term for alloys mainly composed of iron, carbon, and silicon. Cast iron has good castability, wear resistance, shock absorption, and machinability. Currently, it has been widely applied in multiple important fields such as automobiles, construction, national defense, and mechanical manufacturing. The tool rod has a longer overhang, which can meet the requirements of deeper hole processing. The design of a steel cutter bar combined with a hard alloy cutter head brings lower tool costs. The stable blade groove design brings higher accuracy, safety, and stability in drilling applications. The specialized blade groove and material combination ensure good cutting control and excellent hole quality. The design of the drill tip can ensure the requirement of ensuring hole position accuracy even under long overhanging conditions. Crown drills can be used for drilling steel parts in the general machinery industry, drilling heat exchange plates and wind power industry parts, drilling stainless steel parts, and drilling titanium and heat-resistant alloy parts. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

(1) The thread of the drill bit should be coated with standard lubricating grease, and the drill bit loading and unloading device should be used. (2) The drill bit should be straightened and slowly lowered when entering the well, and it should be aligned when reaching the blowout preventer to prevent damage to the PDC cutting teeth. (3) The drilling speed should be slow and the operation should be smooth. It is strictly prohibited to brake or jerk fiercely. During operation, the driller should closely monitor the weight indicator, and in case of resistance, it should not exceed 30kN. Otherwise, the square drill pipe should be connected for circulation, and the method of one punch, two passes, and three reams should be used to pass through. When reaming, the drilling pressure should be controlled below 20kN (lower than 10kN when the drill diameter is less than 215.5mm), and the rotational speed should be less than 50r/min. Large section drilling and non circulating drilling fluid drilling are strictly prohibited. (4) When drilling near the bottom of the well, the pump should be started in advance. When the drill bit is more than 0.5m away from the bottom of the well, it should be slowly moved up and down and the drilling tool should be rotated to fully circulate the drilling fluid. After cleaning the bottom of the well, calibrate the weight indicator. The bottom of the well can only be shaped after the pump pressure is normal. After confirming that the drill bit contacts the bottom of the well, use a speed of about 50r/min and a drilling pressure of 5-20kN to grind in the bottom of the well, with a footage of 0.5-1.0m. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

Preparation work 1. The downhole situation is normal, and the tripping is smooth and unobstructed. 2. The bottom of the well is clean and free from metal debris. 3. The drilling fluid meets the drilling design requirements and the purification equipment operates normally. 4. Use the drill pipe filter well, and its maximum aperture should be smaller than the diameter of the smallest nozzle on the drill bit. Inspect 1. The drill bit model, diameter, and steel stamp markings are consistent with the drill bit manual and outer packaging. 2. The inner and outer cutting teeth (composite pieces) are intact, without broken or missing teeth. 3. The flow channel is unobstructed, and the diameter of the nozzle is checked with a vernier caliper. The nozzle is firmly fixed and meets the hydraulic design requirements. 4. Carefully inspect the wear level, diameter wear degree, and wear characteristics of the inner and outer tooth areas of the old drill bit, analyze the service life, mechanical drilling speed, and desired drilling footage of the drill bit in the formation to be drilled, compare drilling costs and bear risks, and determine whether to re-enter the well. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.

Step drill, also known as step drill or pagoda drill, is mainly used for drilling thin steel plates within 3mm. One drill bit can replace multiple drill bits to process holes of different diameters according to needs, and can achieve one-time processing of large holes without the need to replace the drill bit or drill positioning holes. Step drill, also known as step drill or pagoda drill, is mainly used for drilling thin steel plates up to 3mm. One drill bit can replace multiple drill bits to process holes of different diameters as needed, and can achieve one-time processing of large holes without the need to replace the drill bit or drill positioning holes. Product manufacturing Currently, the overall ladder drill is manufactured using CBN full grinding, mainly made of high-speed steel, hard alloy, etc., with high processing accuracy requirements. According to different processing conditions, surface coating treatment can be carried out to extend the service life of the tool and enhance its durability. Product classification According to the groove shape of the product, it can be divided into three categories: straight groove, spiral groove, and circular groove. According to the number of blades in the product, it can be divided into single edge, double edge, three edge, four edge, and multi edge step drills. If you want to know more about our products, please visit our website https://www.china-drill-bit.com. Hope to cooperate with you.